Standing seam install videos.
We film these on the mock-up roof in our Mt. Juliet shop. A customer roofer installs our panels and trim, and each video takes one detail from start to finish.
Pick a detail
Eight videos, six to twelve minutes each. Each card lists the tools we used, so your crew can load the truck before they start.
Snap-Lock Panel Installation
Setting clips, locking panels together and keeping the run square from eave to ridge.
Toolbox · 6 tools
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Chalk Line
- Speed Square
- Cut-Resistant Gloves
- Safety Glasses
Hand Seaming a Mechanical Seam Panel
Closing the seam by hand at the ends and tight spots the seamer can’t reach.
Toolbox · 7 tools
- Straight-Jaw Hand Seamer
- Offset Hand Seamer
- Mechanical Seamer for the Panel Profile
- Tape Measure
- Dead-Blow Mallet
- Cut-Resistant Gloves
- Safety Glasses
Hemming Panels Over the Drip Edge
Notching and hemming the panel end so it locks over the drip edge.
Toolbox · 9 tools
- Hemming Tool
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Notching Tool
- Tape Measure
- Scribe or Awl
- Cut-Resistant Gloves
- Safety Glasses
Ridge Cap and Z-Closure Installation
Setting and sealing the Z-closures, then fastening the ridge cap on top.
Toolbox · 10 tools
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Chalk Line
- Caulk Gun for Sealant
- Butyl Tape
- Cut-Resistant Gloves
- Safety Glasses
Standing Seam Valley Installation
Laying the valley, cutting panels to the line and hemming them in.
Toolbox · 11 tools
- Straight-Jaw Hand Seamer
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Hemming Tool
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Chalk Line
- Butyl Tape
- Cut-Resistant Gloves
- Safety Glasses
Flashing a Pipe Through Standing Seam
Placing a pipe boot between the seams and sealing it so water runs past.
Toolbox · 9 tools
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Scribe or Awl
- Caulk Gun for Sealant
- Cut-Resistant Gloves
- Safety Glasses
Sidewall and Endwall Flashing
Flashing where the roof meets a wall, along the side and across the top.
Toolbox · 11 tools
- Straight-Jaw Hand Seamer
- Offset Hand Seamer
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Caulk Gun for Sealant
- Butyl Tape
- Cut-Resistant Gloves
- Safety Glasses
Chimney Counterflashing on a Metal Roof
Counterflashing a chimney and building the cricket behind it.
Toolbox · 12 tools
- Straight-Jaw Hand Seamer
- Offset Hand Seamer
- Left-Cut Aviation Snips
- Right-Cut Aviation Snips
- Straight-Cut Aviation Snips
- Notching Tool
- Cordless Drill/Driver with Magnetic Hex Bits
- Tape Measure
- Scribe or Awl
- Caulk Gun for Sealant
- Cut-Resistant Gloves
- Safety Glasses
Call the shop
Talk to the people who formed your panels. Want your crew taught in person? We run hands-on classes at the shop.
615-961-8470