Murfreesboro, TN · Rutherford County

Standing seam panels and trim for Murfreesboro roofers

We roll-form standing seam panels and bend the matching trim in Mt. Juliet, then send them to jobs across Murfreesboro and out to Smyrna, La Vergne, Eagleville and Rockvale. Most orders are ready in 1 to 2 days.

Call615-961-8470Pickup in Mt. Juliet or delivery to your site
For Murfreesboro crews and builders

New houses and the historic overlay

Murfreesboro metal work runs from porch roofs and full roofs on new houses to older houses in the city’s H-1 historic overlay, where the Historic Zoning Commission gets a say on the panel before anybody orders it. We form the panels and bend the trim for both kinds of job.

We sell to the roofers and builders who put the metal up. We don’t install it ourselves. Send a takeoff or a cut list, then pick the order up at the shop or have us bring it to the job.

  • Standing seam roof panels, snap-lock and mechanically seamed
  • Flush wall and soffit panels
  • Trim and flashing bent to your dimensions, including drip edge and Z-bar
  • Clips, screws and high-temp underlayment on the same order
Lead time
1 to 2 daysmost panel orders
Panel gauges
24 & 26 gasteel, roll formed in-house
PAC-CLAD
.032 & .040aluminum, plus 24 ga steel
Forming panels
Since 2011Mt. Juliet, TN
Local specs

Murfreesboro code numbers

Inside city limits, Murfreesboro Building and Codes handles permits and inspections out of 111 West Vine Street. Here’s what matters for a metal roof.

Building code2024 IRC and IBCThe city adopted the 2024 codes with local amendments in ordinance 26-O-34. Plans submitted before January 1, 2027 can be reviewed under the 2024 codes or the codes in effect on August 1, 2026. After that, plans have to meet the 2024 codes.
Re-roof permitsNot if the deck staysOrdinance 26-O-34 exempts a roof covering replacement from a permit as long as the roof deck and framing aren’t replaced, on houses and commercial buildings. Replace sheathing or rafters and you need one. Codes can confirm at 615-893-3750.
Wind and snow loads115 mph, 10 psfFor houses, the city’s amended Table R301.2 sets a 115 mph design wind speed and a 10 psf ground snow load, and says ice barrier underlayment isn’t required. For commercial work, take the numbers off the stamped plans.
Historic overlayApproval before the permitIn the H-1 historic overlay, exterior work you can see from the street needs a Certificate of Appropriateness from the Historic Zoning Commission. The commission’s guidelines list metal as an original roof material and ask for original materials or a close match on replacements. Its conditions on a 2025 East College Street remodel called for 26-gauge Galvalume standing seam on a dormer. Call Planning at 615-893-6441 before you order.
Outside city limitsRutherford County Building CodesThe county runs its own department under the 2024 IBC and IRC. Its FAQ says a re-roof needs a permit only if sheathing, rafters or support beams get replaced or repaired. The county office is at 615-898-7734.

Which of our panels fit Murfreesboro work

1.5″ snap lock (SS4-450)

24 ga Kynar 500 · 26 ga SMP or Galvalume

The everyday panel for porch roofs, bays and full roofs on new houses. The 26 ga Galvalume version is the same material the historic commission called for on that East College Street dormer.

2″ mechanical seam (SSQ210)

Seamed on the roof

For low slopes, long runs and commercial roofs. The seam gets rolled closed on the roof.

1″ flush wall (FWQ100)

Wall, soffit and underdeck

Accent walls, soffits and porch ceilings in the same color as the roof.

Trim and flashing

Bent to your dimensions

Drip edge, Z-bar, ridge and wall flashing to match the panels. Send a sketch with the dimensions and we’ll bend it.

Clips, screws and high-temp underlayment ship on the same order.

Murfreesboro FAQ

Questions from Murfreesboro roofers

Do you deliver metal roofing panels in Murfreesboro?

Yes. We deliver to job sites across Murfreesboro and Rutherford County, out to Smyrna, La Vergne, Eagleville and Rockvale, or you can pick up at the shop at 9485 Lebanon Rd in Mt. Juliet. Most panel orders are ready in 1 to 2 days.

Does Metal Formers install metal roofs in Murfreesboro?

No. We form standing seam panels and bend trim, and we sell them to roofers and builders. If you’re a homeowner, your roofer can order from us.

Do I need a permit to re-roof with metal in Murfreesboro?

Inside city limits, ordinance 26-O-34 exempts a roof covering replacement from a permit as long as the roof deck and framing aren’t replaced. If you replace sheathing or rafters, you need one. Call Building and Codes at 615-893-3750 if you’re not sure. Outside city limits, Rutherford County Building Codes says about the same thing, and you can reach them at 615-898-7734.

Which building code does Murfreesboro use?

The 2024 IRC and IBC, adopted with local amendments in ordinance 26-O-34. Plans submitted before January 1, 2027 can be reviewed under the 2024 codes or the codes in effect on August 1, 2026. After that, plans have to meet the 2024 codes.

What wind speed and snow load does Murfreesboro use?

For houses, the city’s amended Table R301.2 sets a 115 mph design wind speed and a 10 psf ground snow load, and says ice barrier underlayment isn’t required. For commercial work, use the numbers on the stamped plans.

Can I put standing seam on a house in Murfreesboro’s historic overlay?

Often, with approval. Exterior work you can see from the street in the H-1 overlay needs a Certificate of Appropriateness from the Historic Zoning Commission. Its guidelines list metal as an original roof material, and its conditions on a 2025 East College Street remodel called for 26-gauge Galvalume standing seam on a dormer. Call Planning at 615-893-6441 before you order.

Can you roll long panels on a Murfreesboro jobsite?

Yes. If the coil can be delivered to your site, we’ll bring the portable roll former and run the panels there. It saves hauling long panels down the interstate. See jobsite panel runs.

How do I place an order?

Send a takeoff or cut list with an order form, or call Amy at 615-961-8470, Monday to Friday, 7 AM to 4 PM.

Nearby

Also in Rutherford County

Same trucks, same lead time.

  • Smyrna
  • La Vergne
  • Eagleville
  • Rockvale
  • Christiana
  • Lascassas
  • Milton
  • Walter Hill
  • Fosterville

Other town pages

Every town we deliver to
Ready to price it?

Send us your Murfreesboro takeoff

Call Amy at the shop Monday to Friday, 7 AM to 4 PM, or send your takeoff with an order form. Want to see the color first? Request a sample. En español: metalformersinc.com/es.

615-961-8470