Most trim questions we get on the phone come down to one thing: which piece did you mean? A takeoff that says “drip edge” or “valley” could point to three or four different profiles on our list. We bend 30 stock trim and flashing profiles in Mt. Juliet, and this post lays all of them out with the cut width for each, so you can write the right name on your order the first time.
Cut width is the flat width of metal a piece is bent from. It’s the number on our trim and flashing page, and it’s handy when you’re comparing our pieces to a detail on a set of plans or checking what a custom bend will take.
Roof edge and rake
| Profile | Cut width |
|---|---|
| Gable trim | 9″ |
| MF shingle drip edge | 4.2″ |
| 3″ x 3″ flat roof drip edge | 6.5″ |
| T-type drip edge, square | 8″ |
| T-type drip edge, pitched | 8″ |
Drip edge is the one we clarify most. The MF shingle drip edge goes on shingle roofs, the 3″ x 3″ is for flat roofs, and the T-type comes in pitched and square versions.
Ridge, hip and valley
| Profile | Cut width |
|---|---|
| Ridge | 16″ |
| Hip | 14″ |
| Valley, metal to metal | 20″ |
| Valley, shingle to metal | 20″ |
| Valley, shingle to shingle | 20″ |
All three valleys are cut from 20″ of metal. Put the two roof surfaces it joins on the order so we bend the right one.
Walls, headwalls and transitions
| Profile | Cut width |
|---|---|
| Counter flashing | 5.5″ |
| Counter headwall flashing, pitched | 11″ |
| Headwall flashing, pitched | 10″ |
| Sidewall flashing, square | 10″ |
| L flashing | 7″ |
| Transition flashing | 17″ |
| Thru wall | 9″ |
Siding, Z bar and corners
| Profile | Cut width |
|---|---|
| Hardie flashing | 4.5″ |
| Z bar, locking | 4″ |
| Vented Z bar, locking | 4.5″ |
| Pre-flashing Z bar | 7″ |
| Outside corner | 12.125″ |
These go with wall panel and siding work. If you’re running our flush wall panel on a job, ask about Z bar and corners when you order the panels.
Low slope edges and coping
| Profile | Cut width |
|---|---|
| Scupper, TPO | 19″ |
| Hi-lip | Sized to the coping face |
| Hi-lip cleat lock strip | Sized to the coping face |
| Coping cleat lock strip | Sized to the coping face |
The hi-lip and the two cleat lock strips don’t have a fixed cut width. The vertical leg is bent to the face size of the coping, so send us that measurement with the order.
Gutters and downspouts
| Profile | Cut width |
|---|---|
| 6″ box gutter | 21″ |
| 4″ x 5″ downspout | 19.5″ |
| Downspout strap | 2.5″ |
| Gutter hanger | 2.5″ |
Colors, coil and custom bends
Stock profiles come in the same colors as our panels, so your trim matches the roof. Browse the options on our color charts, see them on finished jobs on Roofs by Color, and request a steel sample if the homeowner wants to see the color in daylight before you order.
Crews that bend their own trim can buy 28 gauge flat sheet and coil from us. The coil comes in 50 ft rolls, 21″ wide, sized for a siding brake on site.
If the detail you need isn’t one of the 30, we’ll bend it. Fill out the shop work order form on our order forms page with the panel type, where the piece goes on the roof, your measurements and a drawing. A sketch on paper works. We’ll help you settle the bend, the cut width and the finish.
How to order trim
You can order stock trim with your panels on the panel and flashing order form, or order it by itself. Write the profile name from the tables above, the length and quantity of each piece, and the color. Pick up at 9485 Lebanon Rd in Mt. Juliet, or we’ll deliver to your site. If panels are going on a long run, our jobsite panel runs page covers what we need to roll them on location.
Email your order to office@metalformersinc.com, or call 615-961-8470 for a quote. If you’re not sure which profile fits a detail, call that number and the person quoting your order will help you sort it out.

Leave A Comment